Keyless Remote FobsKeyless Remote Fobs  
Main PageAll VehiclesSearch Nissan Logo

Nissan Sentra Key Fobs


Discount Sentra Keyless Entry Remotes


Misplaced your Nissan Sentra keyless remote? Did your Nissan Sentra key fob stop working? You've come to the right place to find a replacement remote for your Sentra. Pick one up today!


Please check back in a few days if you're not seeing what you wanted.

Vehicle Years Key Fob FCC IDs Remote Part Numbers
2000 - 2004 NHVBU427 NA
2005 - 2006 CWTWB1U429 282686Z 
2007 - 2012 CWTWBU735, KBRASTU15 285E3-EW81D
2011 CWTWB1U415, CWTWB1U733 28268EA


Feel free to contact us if you don't see the correct key fob part numbers or let us know what you are looking for and what is on the back of the remote you are trying to replace. We'll add it to our table in an attempt to help our other customers out.
Dealership Website [Visit Site]


Programing InstructionsNissan Sentra Key Fob Programming Instructions
Need to program or reprogram your key fob? You're in luck because here are some available key fob programming instructions that will work with your vehicle. It should only take you a few minutes and most are fairly easy to do.

1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007
PLEASE READ CAREFULLY BEFORE TRYING! IF AT anytime YOU MAKE A MISTAKE, START AND STOP YOUR CAR, EXIT THE VEHICLE AND START OVER. THE REMOTE CAN BE ONLY PROGRAMMED WITH A MASTER KEY.

1.SIT IN CAR WITH DOORS AND WINDOWS CLOSED.

2.LOCK DOORS WITH POWER DOOR LOCK SWITCH ON DRIVER'S DOOR.

3.PUT IN AND PULL OUT KEY FROM IGNITION APPROX. 8 TIMES OR UNTIL YOU SEE THE HAZARD/TURN SIGNAL LIGHTS FLASH.(older models lights may flash after 4 or 5 times) YOU NEED TO DO THAT IN LESS THEN 10 SEC.

4.WHEN HAZARD LIGHTS FLASH (ON 2005 AND NEWER MODELS THE GAUGE NEEDLES MAY JUMP A LITTLE INSTEAD), PUT KEY IN IGNITION AND TURN TO THE ACC POSITION.(when your hazard lights flash your car is sending a signal to be received by the remote).

5.PRESS LOCK BUTTON ON THE NEW REMOTE TRANSMITTER, LIGHTS SHOULD FLASH AGAIN.

IF YOU HAVE 2 REMOTES, 1 NEW AND 1 OLD OR 2 NEW ONES, PLEASE CONTINUE WITH STEPS 6 AND 7. IF NOT, SKIP TO END.

6.PRESS UNLOCK BUTTON ON DRIVER'S DOOR, THEN LOCK BUTTON ON DRIVERS DOOR, LIGHTS WILL AGAIN FLASH.

7.PRESS LOCK BUTTON ON 2ND NEW OR OLD REMOTE. LIGHTS AGAIN WILL FLASH.

YOU ARE DONE. EXIT VEHICLE AND TRY YOUR REMOTE. IT WILL NOT WORK FROM INSIDE CAR OR WITH KEY IN IGNITION.

Note: if your hazard lights flash after inserting your key in and out, but you can't get the remote to program, you may have a dead battery or the wrong remote. If instructions do not work, do it again but when you get in - shut the door, buckle seat belt and lock doors, then proceed to put key in ignition



Comments:
Leave us a comment if you're not finding what you need or would like to share some information about your vehicle's remote. We'd like to keep our site updated with all the latest information so if you see an error, let us know.


No comments have been submitted. Add yours today!

 
Name:
Comment:
Verification Code:
 

<<- Nissan Rogue Keyless RemotesNissan Titan Keyless Remotes ->>