Keyless Remote FobsKeyless Remote Fobs  
Main PageAll VehiclesSearch Nissan Logo

Nissan Quest Key Fobs


Discount Quest Keyless Entry Remotes


Nissan Quest key fobs help improve safety and ease getting in and out of your Quest. Don't spend a forture trying to replace your Nissan Quest keyless remote. Get yours here today!


Please check back in a few days if you're not seeing what you wanted.

Vehicle Years Key Fob FCC IDs Remote Part Numbers
1996 - 1998 GQ43VT8T 1470101492
1999 - 2002 KOBUTA3T NA
2004 - 2009 KBRASTU15, KBRASTU51 ASTU15 


Feel free to contact us if you don't see the correct key fob part numbers or let us know what you are looking for and what is on the back of the remote you are trying to replace. We'll add it to our table in an attempt to help our other customers out.
Dealership Website [Visit Site]


Programing InstructionsNissan Quest Key Fob Programming Instructions
If you're purchasing a new remote and don't know how to program it or you just need to get it working after a battery change, here are some key fob programming instructions to help you get started. You should be back working in no time.

1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009
PLEASE READ CAREFULLY BEFORE TRYING! IF AT anytime YOU MAKE A MISTAKE, START AND STOP YOUR CAR, EXIT THE VEHICLE AND START OVER. THE REMOTE CAN BE ONLY PROGRAMMED WITH A MASTER KEY.

1.SIT IN CAR WITH DOORS AND WINDOWS CLOSED.

2.LOCK DOORS WITH POWER DOOR LOCK SWITCH ON DRIVER'S DOOR.

3.PUT IN AND PULL OUT KEY FROM IGNITION APPROX. 8 TIMES OR UNTIL YOU SEE THE HAZARD/TURN SIGNAL LIGHTS FLASH.(older models lights may flash after 4 or 5 times) YOU NEED TO DO THAT IN LESS THEN 10 SEC.

4.WHEN HAZARD LIGHTS FLASH (ON 2005 AND NEWER MODELS THE GAUGE NEEDLES MAY JUMP A LITTLE INSTEAD), PUT KEY IN IGNITION AND TURN TO THE ACC POSITION.(when your hazard lights flash your car is sending a signal to be received by the remote).

5.PRESS LOCK BUTTON ON THE NEW REMOTE TRANSMITTER, LIGHTS SHOULD FLASH AGAIN.

IF YOU HAVE 2 REMOTES, 1 NEW AND 1 OLD OR 2 NEW ONES, PLEASE CONTINUE WITH STEPS 6 AND 7. IF NOT, SKIP TO END.

6.PRESS UNLOCK BUTTON ON DRIVER'S DOOR, THEN LOCK BUTTON ON DRIVERS DOOR, LIGHTS WILL AGAIN FLASH.

7.PRESS LOCK BUTTON ON 2ND NEW OR OLD REMOTE. LIGHTS AGAIN WILL FLASH.

YOU ARE DONE. EXIT VEHICLE AND TRY YOUR REMOTE. IT WILL NOT WORK FROM INSIDE CAR OR WITH KEY IN IGNITION.

Note: if your hazard lights flash after inserting your key in and out, but you can't get the remote to program, you may have a dead battery or the wrong remote. If instructions do not work, do it again but when you get in - shut the door, buckle seat belt and lock doors, then proceed to put key in ignition



Comments:
Leave us a comment if you're not finding what you need or would like to share some information about your vehicle's remote. We'd like to keep our site updated with all the latest information so if you see an error, let us know.

John Bonadeo says:
09-20-2013
Do you have a keyless remote and/or how to program the remote for a Nissan Quest 2011. There is no ignition switch on this vehicle at all. It only has a push button.
 
boerger tim says:
05-08-2017
i need to program a fob for 2016 Nissan quest
 

 
Name:
Comment:
Verification Code:
 

<<- Nissan Pathfinder Keyless RemotesNissan Rogue Keyless Remotes ->>